Spacer Ring
Распорное Кольцо
Anillo Espaciador
OEM Spacer Ring 199100360134 precision‑machined for the Shacman X5000 mechanical assemblies. This essential 199100360134 clearance component maintains exact distance between mating parts, ensuring proper alignment and bearing preload in rotating assemblies.
Manufactured from high‑grade steel with precise thickness tolerance and parallel faces, the Spacer Ring 199100360134 provides consistent dimensional control that prevents the binding or excessive play that causes premature wear.
Replacing a worn or incorrect spacer with the genuine 199100360134 component restores proper assembly clearances and protects adjacent bearings, gears, and shafts from misalignment damage.
| Parameter | Specification |
|---|---|
| OEM Part Number | 199100360134 |
| Product Name | Spacer Ring |
| Brand / Model | Shacman X5000 |
| Material | High‑Grade Steel with Phosphate Coating |
| Inner Diameter | Approximately 36.00 mm |
| Outer Diameter | Approximately 45.00 mm |
| Thickness | 3.00 mm ± 0.02 mm |
| Surface Finish | Precision ground parallel faces |
| Corrosion Protection | Phosphate conversion coating with oil film |
| Application | Shacman X5000 rotating assembly clearance and preload adjustment |
The 199100360134 spacer ring establishes and maintains the precise axial distance between components in Shacman X5000 rotating assemblies such as transmission shafts, differential carriers, and wheel hub bearings.
In bearing arrangements, the correct spacer thickness determines the internal clearance or preload that directly affects bearing life, running temperature, and the noise level of the rotating assembly during operation.
The Spacer Ring 199100360134 is manufactured with precision‑ground parallel faces and tight thickness tolerance, ensuring that the assembled stack‑up dimension meets the engineering specification for the specific application.
The 199100360134 ring is machined from high‑grade steel with parallel faces ground to a tolerance of ±0.02 mm, ensuring the spacer does not introduce angular misalignment into the assembly.
The phosphate coating provides corrosion protection during storage and service, while the oil film helps prevent fretting corrosion at the interface with adjacent components under load.
The 199100360134 spacer ring is installed by sliding it onto the shaft or into the housing bore between the components that require separation. The mating surfaces must be clean before assembly.
Spacer thickness should be verified against the assembly specification during rebuilds. Using an incorrect thickness spacer changes the designed internal clearances and can lead to premature component failure.
Each production batch of 199100360134 spacer rings undergoes dimensional inspection using precision micrometers to verify inner diameter, outer diameter, thickness, and parallelism against specifications.
Material hardness and surface finish are verified to ensure the ring maintains its dimensional stability under the compressive loads experienced in clamped rotating assemblies during operation.
A worn 199100360134 spacer ring may show fretting marks, surface galling, or measurable thickness reduction on its contact faces, indicating relative movement between assembled components.
Increased noise, vibration, or heat from a bearing assembly can result from incorrect preload caused by a spacer ring that has worn thin or been replaced with an incorrect thickness alternative.
During component overhaul, all spacer rings should be inspected for wear and measured for thickness. Any spacer showing dimensional change or surface damage must be replaced with the correct genuine part.
The 199100360134 spacer ring is specifically dimensioned for designated rotating assemblies in the Shacman X5000 driveline and chassis components, matching factory specifications exactly.
Fleet workshops should maintain an assortment of genuine spacer rings for replacement during component overhauls, ensuring correct clearances are restored and maintained for reliable operation.
Aftermarket spacer rings with incorrect dimensions can compromise assembly integrity. We supply only the authentic Shacman X5000 Spacer Ring 199100360134 built to stringent OEM dimensional standards.
Each ring is individually packaged with protective oil coating. The part number 199100360134 is clearly printed on the packaging for immediate identification and verification.
Our international logistics network ensures genuine 199100360134 spacer rings are available for dispatch to dealerships and fleet maintenance facilities across all major continents.
Single precision spacer ring with phosphate coating and ground faces. Protective oil film preserves the surface during storage.
Expert guidance on spacer ring selection and assembly procedures. We help ensure your 199100360134 ring provides correct clearance control.
For current stock availability on the genuine Spacer Ring 199100360134, please use the contact buttons above.
