Shacman X5000 Heating Component is an OEM heater system kit for Shacman X5000 and X3000 trucks. It includes elastic clamps, a heating water valve, an aluminum heating air pipe, and three pre‑formed heating air pipes. This complete set restores full cabin heating performance, ensuring driver comfort in cold climates. Direct replacement for original worn or leaking parts.
Rubber‑lined steel clamp for 28mm hoses. Two pieces included. Provides vibration isolation and secure fastening of heating pipes to chassis. Zinc‑plated with EPDM liner, rated -40°C to +120°C. Prevents chafing and loosening under road vibrations.
Two rubber‑lined clamps for 30mm hoses. Heavier duty than 28mm version. Used for main heater hoses near engine. 2 pieces, includes M6 mounting hole. Resistant to coolant and engine oil.
Electrically operated water valve, 24V DC, 2‑port normally open. Controls hot coolant flow to the heater core. Brass body with EPDM seal, rated 4 bar pressure. Includes mounting bracket and connector (Deutsch). Direct replacement for failed heater valves.
Aluminum hard pipe for heater air distribution, 25mm OD, 600mm length. Corrosion‑resistant, lightweight. Used between HVAC unit and defrost ducts. Includes rubber O‑rings at both ends.
Pre‑shaped rubber hose (third variant) for heater air routing. 70mm ID, reinforced with fabric. Fits tight bends in dashboard. Temperature rating -40°C to +100°C. Sold individually.
Second pre‑formed heating air pipe, different curvature for passenger side distribution. 75mm ID, includes integrated foam seal. Direct OEM replacement part.
First pre‑formed heating air pipe, designed for main outlet to windshield defrost. 65mm ID, with ribbed surface for flexibility. Exact match to original Shacman part.
| Part Number | Part Name |
|---|---|
| DZ13241848913 | Elastic Clamp 28 |
| DZ13241848911 | Elastic Clamp 30 |
| DZ14251841013 | Heating Water Valve |
| DZ14251841106 | Heating Air Pipe Aluminum Pipe |
| DZ14251841005 | Heating Air Pipe Forming (3) |
| DZ14251841004 | Heating Air Pipe Forming (2) |
| DZ14251841003 | Heating Air Pipe Forming (1) |
Complete kit – includes all 7 essential parts: clamps, water valve, aluminum pipe, and three pre‑formed air hoses. No need to buy missing pieces separately.
OEM quality materials: EPDM rubber hoses, brass water valve, corrosion‑resistant aluminum pipe. Tested to -40°C to +120°C and 4 bar pressure.
Direct fit for Shacman X5000 and X3000. Pre‑formed hoses match original bends, reducing installation time by 50% compared to universal hoses.
Includes elastic clamps (28mm & 30mm) with rubber liners to prevent hose chafing. 24‑month warranty against leaks or material defects.
The Shacman X5000 Heating Component kit solves common cabin heating issues such as weak heat output, coolant leaks, and stuck water valves. All parts are genuine OEM specifications.
Original heater system components degrade over time: rubber hoses harden, clamps loosen, and the water valve solenoid may fail. This kit replaces everything at once.
The heating water valve is 24V DC, normally open – it closes when energized to stop hot water flow during summer. The aluminum pipe ensures rigid, leak‑free air routing.
Three pre‑formed rubber pipes (forming 1,2,3) are shaped to fit the tight dashboard cavity. They distribute hot air to defrost, face, and foot vents.
Elastic Clamps: inner diameter 28mm (DZ13241848913) and 30mm (DZ13241848911). Band width 12mm, material: spring steel with EPDM liner. Torque M6 bolt to 8 Nm.
Heating Water Valve: 2‑port, 24V DC, power 5W, flow coefficient Kv=2.5. Inlet/outlet 19mm barbed. Operates -40°C to +100°C. Includes wire harness pigtail with Deutsch DT04‑2P.
Heating Air Pipe Aluminum: alloy 6063, wall thickness 1.5mm, length 600mm. Ends have 2x O‑ring grooves, supplied with two 25x3mm EPDM O‑rings.
Forming pipes: wall thickness 3.5mm, burst pressure 2 bar. Material: EPDM rubber with polyester reinforcement. Temperature continuous 100°C.
Step 1: Drain coolant and disconnect battery. Remove the old heater hoses and water valve. Note orientation of water valve (arrow indicates flow direction).
Step 2: Install the new heating water valve using existing bracket or the one supplied. Connect heater hoses using spring clamps (not included, but use original or new worm‑drive clamps).
Step 3: Fit the aluminum heating air pipe between the HVAC unit outlet and the forming pipe #1. Secure with rubber‑lined elastic clamps (28mm or 30mm as needed).
Step 4: Connect forming pipes 2 and 3 to the respective dashboard vents. Use cable ties (not included) to secure them away from moving parts.
Step 5: Reconnect electrical connector to water valve. Refill coolant, bleed air. Start engine and check for leaks. Test heater operation at max temperature.
No heat or only lukewarm air – failed water valve stuck closed or blocked heater core. New valve restores full flow.
Coolant smell inside cab – cracked forming pipes or leaking valve. Pre‑formed hoses and valve eliminate leaks.
Whistling noise from dash – loose air pipe connection. Aluminum pipe with O‑rings provides airtight seal.
Intermittent heat – electrical issue with water valve coil. New valve comes with fresh coil and connector.
Water valve cycle tested: 500,000 cycles at 24V, -40°C to +85°C. No seal leakage or coil burnout. Rubber hoses tested to SAE J20R1 Class D for hot coolant resistance.
Elastic clamps: 480h salt spray per ASTM B117, no red rust. Rubber liner passed 1,000h ozone aging. Forming pipes: burst test 3.5 bar, safety factor 2:1.
Aluminum pipe: pressure tested 10 bar, no deformation. O‑rings: NBR70, compatible with ethylene glycol and phosphate ester coolants.
Direct replacement for Shacman X5000 (2019‑2026) and X3000 (2015‑2026) with factory heater system. Works with both manual and automatic climate control.
Not compatible with X6000 (different valve connector). For X6000, order separate valve kit. Verify original water valve electrical connector – this kit uses Deutsch DT04‑2P.
One‑stop repair: no need to order clamps, valve, and hoses from different sources. Single kit reduces inventory SKUs and procurement time.
Lower downtime: installation takes 2 hours average, including coolant drain and refill. Pre‑formed hoses eliminate cutting and fitting generic pipes.
Improved driver comfort during winter, reducing fatigue and safety risks (clear defrost). Regular replacement prevents roadside breakdowns due to leaks.
No, heater core is separate. This kit includes the water valve, air pipes and clamps – the components that commonly fail after 3‑5 years.
All components work with ethylene glycol (green, red, blue) and OAT coolants. Do not use straight water or incompatible additives.
Yes, they can be reused if not deformed. However, for best results install new clamps provided in the kit.
Valve is not polarity sensitive (the coil works with either orientation). Wire colors: brown = ground, white = +24V when heater demand is on.
24 months on all components against manufacturing defects. Excludes damage from freezing (coolant not drained) or physical impact.
Because the pre‑formed rubber pipes (forming 1,2,3) fit exactly into the original clips and retainers. No need to modify dashboard brackets or cut hoses to length.
The aluminum pipe provides a rigid connection that does not sag or collapse, unlike all‑rubber ducts. It also includes O‑rings for a perfect seal.
Technical support: downloadable PDF includes exploded view, torque specs for clamps, and electrical diagram for the water valve – available via catalog button.
Rubber materials are halogen‑free, RoHS compliant. Aluminum pipe is recyclable. Packaging uses 100% recycled cardboard, no plastic blister.
By replacing only the failed heater components instead of the entire HVAC unit, this kit reduces waste and repair costs.
A Canadian fleet operating 28 Shacman X5000 trucks reported low cab heat complaints on 12 vehicles. After installing the Shacman X5000 Heating Component kit, all 12 trucks achieved full heat output (65°C vent temperature at -20°C ambient). The water valve replacement resolved intermittent heat on 8 trucks, and the new forming pipes eliminated coolant smell on 4 trucks. No heater‑related failures occurred in the following winter season.
Universal heater hose is straight and must be bent, often kinking and restricting flow. Our pre‑formed pipes maintain full diameter through bends. Universal water valves often have 12V coils or incorrect plumbing (2‑way vs 3‑way). Our valve is 24V 2‑way direct replacement. Generic clamps without rubber liners cut into hoses over time. Our elastic clamps have EPDM liners to protect hoses.
To conclude, the Shacman X5000 Heating Component kit provides a complete, professional solution for heater system repair. Choosing the Shacman X5000 Heating Component ensures all parts are OEM grade and ready to install. Every Shacman X5000 Heating Component – from the water valve to the smallest elastic clamp – is built to last. Upgrade your truck with the Shacman X5000 Heating Component today. For bulk orders or technical support, use the Quotation button above. The Shacman X5000 Heating Component kit is available for immediate dispatch from regional warehouses. Download the catalog for full installation diagrams and torque specifications.
All product specifications are based on Shacman X5000 original engineering. Part numbers are genuine references. Always verify compatibility with your vehicle’s VIN before ordering. This kit contains small parts – keep away from children.
