Clamp Pad (Work Light)
Зажимная Прокладка Фары
Almohadilla de Sujeción
OEM Clamp Pad (Work Light) 81.62940.2076 precision‑molded for the Shacman X5000 heavy‑duty truck. This specialized 81.62940.2076 cushioning component secures work light assemblies to their mounting brackets, absorbing vibration and preventing loosening.
Manufactured from UV‑stabilized elastomeric material with excellent compression set resistance, the Clamp Pad (Work Light) 81.62940.2076 maintains consistent clamping force through temperature extremes and prolonged exposure.
Replacing worn or missing pads with the genuine 81.62940.2076 component restores proper light fixture stability and prevents the damage caused by loose mounting hardware.
| Parameter | Specification |
|---|---|
| OEM Part Number | 81.62940.2076 |
| Product Name | Clamp Pad (Work Light) |
| Brand / Model | Shacman X5000 |
| Material | EPDM Rubber with UV Stabilizers |
| Hardness | 70 Shore A |
| Pad Dimensions | 42.00 mm × 28.00 mm × 8.00 mm |
| Mounting Hole Diameter | 8.50 mm through hole |
| Operating Temperature | -40°C to +120°C |
| Compression Set | ≤ 20% after 22 hours at 100°C |
| Application | Shacman X5000 work light bracket cushioning |
The 81.62940.2076 clamp pad serves as the interface between the work light housing and its metal mounting bracket. It creates a high‑friction, vibration‑absorbing layer that prevents the light assembly from rotating or loosening.
Heavy trucks experience constant vibration from the engine, driveline, and road surface irregularities. Without a properly functioning pad, this energy transfers directly into the light fixture mounting bolts.
The Clamp Pad (Work Light) 81.62940.2076 also compensates for minor surface irregularities between the bracket and light housing, distributing clamping force evenly to prevent stress concentrations on the plastic light body.
The 81.62940.2076 pad is formulated from EPDM rubber containing ultraviolet light stabilizers. This material resists the surface cracking and hardening that affects ordinary rubber after prolonged exposure to sunlight.
EPDM also offers excellent resistance to ozone, road salt, and the cleaning chemicals used in commercial vehicle washing. The pad retains its elasticity and appearance throughout its service life.
The 81.62940.2076 pad is placed between the bracket and the light mounting tab before the bolt is inserted. The bolt should be tightened until the pad compresses slightly, but not to the point where it extrudes from the joint.
Over‑tightening crushes the pad and destroys its vibration‑damping capability. The correct torque allows the Clamp Pad (Work Light) 81.62940.2076 to perform its cushioning function while maintaining secure retention.
Each production lot of 81.62940.2076 pads undergoes hardness testing to verify Shore A values within the specified tolerance. Material samples are also tested for tensile strength and elongation at break.
Accelerated UV weathering tests expose sample pads to concentrated ultraviolet radiation for extended periods. Post‑exposure inspection confirms that surface cracking does not occur within the rated service interval.
A hardened or cracked 81.62940.2076 pad loses its ability to grip the light housing and absorb vibration. The work light may begin to oscillate noticeably, especially at idle or on rough road surfaces.
A pad that has taken a permanent compression set will appear flattened and will not recover its original thickness when the mounting bolt is loosened. Such pads must be replaced immediately.
During routine vehicle inspections, work light mounting points should be checked for pad condition. Replacing worn Clamp Pad (Work Light) 81.62940.2076 units prevents the progressive damage that leads to light bracket failure.
The 81.62940.2076 pad is specifically dimensioned for the Shacman X5000 work light mounting interface. Using generic washers or grommets does not provide the same vibration isolation.
Fleet operators should include these pads in their lighting system maintenance kits. Keeping genuine 81.62940.2076 pads readily available supports quick repairs and maintains proper light alignment.
Aftermarket pads made from inferior rubber compounds deteriorate rapidly in harsh environments. We supply only the authentic Shacman X5000 Clamp Pad (Work Light) 81.62940.2076 with full OEM material certification.
Each pad is packaged in a sealed polybag to prevent ozone degradation during storage. The part number 81.62940.2076 is clearly printed on the label for immediate identification.
Our international supply chain ensures that genuine 81.62940.2076 clamp pads are available for prompt delivery to workshops and fleet maintenance facilities around the world.
Single clamp pad in sealed protective packaging. Sold individually or in multi‑pack quantities for fleet maintenance programs.
Expert guidance on clamp pad installation and proper bolt torque. We help ensure your 81.62940.2076 pads deliver optimal vibration isolation.
For current stock availability and pricing on the genuine Clamp Pad (Work Light) 81.62940.2076, please use the contact buttons above.
