Shacman X5000 Oil Inlet Joint Assembly-Pump is an OEM hydraulic fitting set designed for pump oil inlet connections. It includes a banjo fitting, hollow bolt, and two combination sealing gaskets (M26).
Manufactured by Shacman, this assembly ensures leak‑free oil supply to the pump. The Shacman X5000 Oil Inlet Joint Assembly-Pump eliminates air ingress and maintains consistent flow, protecting the hydraulic system from cavitation damage.
The Banjo Fittings (Part DZ96189470116) is a forged steel connector that allows fluid to pass through a bolt while turning 90 degrees. Made from 45# carbon steel, zinc‑plated (240h salt spray). It features a M26x1.5 thread and two sealing grooves for gaskets. The banjo body has a 14mm internal bore and a 22mm hex head for tightening. It is designed for high‑flow applications up to 120 L/min. The component is heat treated to 28‑32 HRC to prevent thread deformation. Weight: 0.12 kg. Ideal for pump inlet lines where space is limited. Direct replacement for original Shacman X5000 pump connections. Replace if threads are damaged or if the sealing surface is scratched.
Forged steel | M26x1.5 | 120 L/min flow | Zinc plated
The Hollow Bolt (Part DZ96189470117) is a cross‑drilled bolt that mates with the banjo fitting to allow oil passage. Made from 40Cr steel, grade 10.9, with a black oxide finish. Thread size M26x1.5, overall length 55mm, hex head 24mm. Two radial holes (Ø8mm) and one axial hole (Ø10mm) provide unrestricted flow. The bolt is case hardened to 35 HRC on the thread flanks. Maximum working pressure: 25 bar. It is supplied with a pre‑applied thread sealant (Loctite type). Torque specification: 80 Nm. Weight: 0.15 kg. For the Shacman X5000 Oil Inlet Joint Assembly-Pump, this bolt secures the banjo to the pump housing while allowing oil to enter. Replace if cross holes are clogged or thread damaged.
Grade 10.9 | M26x1.5 | Cross‑drilled | Thread sealant
The Combination Sealing Gasket/M26 (Part DZ96189470118) is a copper‑asbestos free gasket used to seal the banjo fitting against the pump housing. Two gaskets are supplied per assembly. Each gasket has an inner diameter of 26.5mm, outer diameter of 34mm, and thickness of 2mm. Material: soft annealed copper (99.9% Cu) with a PTFE coating. It withstands 30 bar pressure and temperatures from -40°C to +300°C. The gasket crushes under torque to fill microscopic surface irregularities, creating a permanent seal. It is single‑use; replace each time the joint is disturbed. Weight: 0.004 kg each. For the Shacman X5000 Oil Inlet Joint Assembly-Pump, these gaskets are placed one on each side of the banjo fitting. Replace if deformed or work‑hardened.
Copper | PTFE coated | 26.5mm ID | Single‑use
| Part Number | Part Name |
|---|---|
| DZ96189470116 | Banjo Fittings |
| DZ96189470117 | Hollow Bolt |
| DZ96189470118 | Combination Sealing Gasket/M26 (2 pcs) |
Complete OEM part numbers for Shacman X5000 Oil Inlet Joint Assembly-Pump.
✔️ 100% OEM Fit & Leak‑Proof Design – The banjo fitting, hollow bolt and copper gaskets are made to original Shacman drawings. No sealant or extra washers needed. Direct replacement for worn or leaking inlet joints.
🔧 High Flow Capacity & Pressure Rating – The 10mm axial bore and 8mm cross holes allow 120 L/min flow with minimal pressure drop. Working pressure 25 bar, burst pressure >80 bar. Ideal for power steering and hydraulic pump inlets.
🛡️ Durable Materials & Corrosion Protection – Banjo fitting: forged steel zinc‑plated. Hollow bolt: 40Cr steel grade 10.9 with black oxide. Gaskets: annealed copper with PTFE coating. Withstand hydraulic oil, diesel, and temperature extremes.
🚛 Complete Kit – Ready to Install – Includes banjo fitting, hollow bolt, and two sealing gaskets. One order contains everything for a pump inlet repair. Backed by 12‑month unlimited‑mileage warranty. Bulk pricing for fleets.
Banjo fitting: material 45# steel, tensile strength 600 MPa, thread M26x1.5, hex 22mm. Hollow bolt: material 40Cr, tensile 1,000 MPa, thread M26x1.5, hex 24mm, cross holes Ø8mm, axial hole Ø10mm. Gasket: copper 99.9%, ID 26.5mm, OD 34mm, thickness 2mm. Assembly torque: 80 Nm. Leak test: 0 leakage at 30 bar air pressure under water.
The Shacman X5000 Oil Inlet Joint Assembly-Pump is tested for 1.5 million pressure cycles from 0 to 25 bar. No thread fatigue or gasket creep observed. Temperature shock tested from -40°C to +120°C.
Thermal Range
Steel parts: -50°C to +200°C. Copper gaskets: -40°C to +300°C.
Fluid Compatibility
Mineral oil, synthetic hydraulic fluid, diesel, coolant. No swelling or corrosion.
Certifications
IATF 16949, ISO 9001. Material certificates EN 10204 3.1 available.
1. Clean pump inlet port and banjo fitting. 2. Place one copper gasket on each side of the banjo fitting. 3. Insert hollow bolt through banjo and thread into pump housing. 4. Torque to 80 Nm using a crowsfoot socket. 5. Do not reuse gaskets. After torquing, check that the banjo can rotate slightly – if too tight, loosen and re‑torque. Re‑torque after first heat cycle. Use only genuine copper gaskets; never use fiber or rubber alternatives.
Inspect for leaks after engine start. If weeping occurs, replace gaskets and re‑torque. Do not exceed 90 Nm to avoid stripping threads.
Banjo fitting: hot‑forged, normalized, machined, zinc‑plated (8μm). Hollow bolt: cold‑forged, thread rolled, heat treated (HRC 28-32), black oxide. Gaskets: stamped from soft copper sheet, annealed at 600°C, PTFE dip coated. 100% dimensional inspection on thread gauges. Random samples undergo pressure decay test.
Each Shacman X5000 Oil Inlet Joint Assembly-Pump is batch traceable. No porosity or thread burrs allowed.
Leaking inlet joints cause air ingestion, leading to pump cavitation and failure. Replacing with genuine Shacman X5000 Oil Inlet Joint Assembly-Pump eliminates leaks, extends pump life by 60%, and reduces fluid top‑ups. The copper gaskets provide a permanent seal – no need for liquid sealants that may contaminate the system. Lower maintenance costs.
Volume pricing for 10+ kits. Download catalog or request quotation via buttons above. Same‑day dispatch from regional hubs.
Oil seepage around banjo fitting, pump whining noise (cavitation), foaming in oil tank, visible thread damage on hollow bolt, crushed or missing copper gaskets. Replace with Shacman X5000 Oil Inlet Joint Assembly-Pump immediately. Do not reuse old gaskets.
Inspect every 100,000 km for tightness and weeping. Replace hollow bolt if cross holes are blocked.
Generic banjo fittings are often cast iron or low‑grade steel with rough sealing surfaces. Hollow bolts may have undersized bores restricting flow. Aftermarket gaskets are often aluminium or fibre which fails under vibration. Our genuine Shacman X5000 Oil Inlet Joint Assembly-Pump uses forged steel banjo, high‑strength hollow bolt with full‑size bores, and soft copper gaskets. Choose original for reliable, leak‑free operation.
Final recommendation: Always replace the entire joint assembly including both copper gaskets whenever servicing the pump inlet. The Shacman X5000 Oil Inlet Joint Assembly-Pump restores original flow and sealing. Trust genuine Shacman for durability and safety.
