Shacman X5000 A-C Cab Components is a comprehensive OEM HVAC and air distribution kit for Shacman X5000 and X3000 cabs. This complete set includes welding studs, reed nuts, filter screen, drying tank bracket, fixed clips, filter housing, elastic clamps, defrosting ducts, foot blowing ducts, drainage components, water valves, evaporator/condenser connections, heating hoses, AC body assembly, warning sign, pipe clamps, cable ties, and all mounting hardware (bolts, nuts, washers). Perfect for cab climate control restoration.
M8 welding stud for mounting brackets on cab floor. 3 pieces. Zinc‑plated, provides strong threaded anchor point for HVAC components.
ST4.8 self-tapping reed nuts for plastic panels. 4 pieces. Secure air ducts without separate washers. Fast assembly.
Nylon mesh filter screen for HVAC blower inlet. Traps dust and debris before evaporator. Washable, reusable.
Powder‑coated steel bracket for air dryer tank. Includes rubber isolator to reduce vibration transmission to cab.
Plastic spring clip for securing AC lines to firewall. Holds 15mm diameter pipes. Quick release design.
Complete plastic housing for cabin air filter. Includes cover and seal. Accepts standard 280x200x30mm filter.
Rubber‑lined steel clamp for 30mm hoses. 2 pieces. Used for AC suction and liquid lines. Vibration dampening.
29mm rubber‑lined clamp for smaller AC hoses. 2 pieces. Prevents chafing and secures lines to chassis.
Left windshield defrost air duct. PP plastic with foam seal. Directs hot air to driver side windshield.
Mirror right defrost duct. Passenger side. Includes integrated clip for instrument panel attachment.
Upper left footwell air duct. Channels warm/cool air to driver’s feet from HVAC unit.
Right upper foot duct for passenger side. Injection molded ABS, includes mounting holes.
Lower left foot duct. Extends airflow to floor level. Secures with two screws.
Lower right foot duct, symmetrical. Ensures even heating distribution across cab floor.
Rubber cover for evaporator drain hole. 2 pieces. Prevents air leakage and water backflow.
Stamped steel bracket for mounting cabin heater water valve. Includes pre‑welded nuts.
PVC corrugated drain hose, 25mm ID, 600mm length. Routes condensate from evaporator to outside.
Molded rubber hose for heater core outlet. EPDM, rated 120°C, burst pressure 4 bar.
Protective rubber sleeve for AC line pass‑through firewall. Seals against water and noise.
Aluminum AC line from evaporator to compressor. Includes O‑ring seals. Length 1.2m.
AC hose assembly connecting condenser to evaporator. Block type fitting, with service port.
Pre‑formed heater hose (x2 pieces) for engine to heater core. EPDM rubber, ID 19mm.
Second pre‑formed heater hose for return line. Different bend shape, same high‑quality EPDM.
Metal bracket supporting heater core inside HVAC unit. Powder coated, anti‑rust.
Complete heater core assembly with aluminum fins and tubes. For hot water heating, 12.7mm ports.
Main HVAC unit for right‑hand drive X3000/X5000. Independent blower power, includes evaporator and heater core.
Adhesive label with AC system pressure warnings. Multilingual, high‑temp polyester.
Single plastic clamp for AC or heater lines to chassis. Snap‑lock, reusable.
2.5x100mm nylon cable ties for harness and hose routing. UV stabilized, 18kg tensile strength.
M6x16mm flange bolt, class 10.9, 3 pieces. For bracket mounting. Pre‑applied threadlocker.
M6x20mm flange bolt, 1 piece. For securing HVAC unit to firewall. Torque 12 Nm.
M8x20mm flange bolt, 5 pieces. For heavy brackets and drying tank. Torque 25 Nm.
M8x25mm flange bolt, 3 pieces. For compressor mount and stud attachments.
M8x40mm flange bolt, 2 pieces. For deep bracket clamping.
ST4.2×13 tapping screw with flat washer assembly, 4 pieces. Secures ducts to plastic housings.
ST4.8×16 tapping screw with washer, 4 pieces. For heavier duct and bracket attachment.
M4x10 cross slotted screw with captive washer. 4 pieces. For warning sign and small trim.
M6 standard hex nut, class 8. 2 pieces. For bolted joints where flange nut not needed.
M6 flat washer, 6.4x12x1.6mm, 2 pieces. Load distribution under bolts.
M6 spring lock washer, 2 pieces. Provides vibration resistance under hex nuts.
| Part Number | Part Name |
|---|---|
| DZ93189777172 | Welding Stud |
| 06.13189.0099 | Reed Nuts/ST4.8-2-MAN183-B1 |
| 81.61910.0011 | Filter Screen At Air Inlet Of Fan |
| DZ13241821204 | Drying Tank Bracket Assembly |
| DZ13241821502 | Fixed Clip (2) |
| DZ13241841430 | Filter Housing Assembly |
| DZ13241848911 | Elastic Clamp 30 |
| DZ13241848912 | Elastic Clamp 29 |
| DZ14251160200 | Left Defrosting Duct |
| DZ14251160210 | Right Defrost Air Duct |
| DZ14251160220 | Left Foot Blowing Duct (Upper) |
| DZ14251160230 | Right Side Foot Blowing Air Duct |
| DZ14251161900 | Left Foot Blowing Air Duct (Down) |
| DZ14251161950 | Right Side Foot Blowing Air Duct |
| DZ14251841001 | Drainage Plug Cover |
| DZ14251841009 | Electric Water Valve Bracket |
| DZ14251841011 | Drainage Pipe |
| DZ14251841012 | Front Water Outlet Pipe |
| DZ14251841021 | Rubber Sheath |
| DZ14251841043 | Evaporator Compressor Connecting |
| DZ14251841078 | Condenser Evaporator Connection |
| DZ14251841107 | Heating Water Pipe Forming Hose |
| DZ14251841108 | Heating Water Pipe Forming Hose |
| DZ14251841110 | Air Heating Bracket |
| DZ14251841116 | Heating Component |
| DZ14251841122 | AC Body Assembly (X3000/RHD/Fan Power Independent) |
| DZ14251841204 | AC System Warning Sign (X3000) |
| DZ14251845007 | Pipe Clamp |
| DZ93189777161 | Ordinary Narrow Cable Tie |
| Q1840616T1F31 | Hexagon Flange Bolt |
| Q1840620T1F31 | Hexagon Flange Bolt |
| Q1840820T1F31 | Hexagon Flange Bolt |
| Q1840825T1F31 | Hexagon Flange Bolt |
| Q1840840T1F31 | Hexagon Flange Bolt |
| Q221B4213F60 | Cross Recessed Pan Head Tapping Screw And Flat Washer Assembly |
| Q221B4816F60 | Cross Recessed Pan Head Tapping Screw And Flat Washer Assembly |
| Q230B0410F60 | Cross Slotted Screw And Washer |
| Q340B06F60 | Type 1 Hex Nut |
| Q401B06F60 | Flat Washer |
| Q40306F60 | Spring Washer* |
Complete solution – 40+ components including all ducts, brackets, hoses, AC lines, hardware, and the main HVAC unit. No missing parts.
OEM quality – all parts match Shacman X5000/X3000 original specifications. EPDM hoses, aluminum AC lines, and corrosion‑resistant fasteners.
Restores full HVAC function: defrost, footwell, main vents, heating and cooling. Independent blower motor on AC body assembly.
Includes all mounting hardware: flange bolts, tapping screws, nuts, washers, spring washers, cable ties, and reed nuts – ready to install.
The Shacman X5000 A-C Cab Components kit is engineered for complete cab climate system overhaul. It covers everything from the main HVAC unit (AC body assembly) to every air duct, drain pipe, water valve bracket, and AC line.
Original components often fail due to aging plastics, clogged filter screens, or corroded heater cores. This kit replaces all critical parts with fresh OEM stock.
Kit includes both left and right defrost ducts, upper and lower foot ducts, ensuring even air distribution. The drainage components prevent water buildup inside the HVAC casing.
All fasteners – from welding studs to spring washers – are included. No need to recycle old rusty bolts or mismatched screws.
AC Body Assembly (DZ14251841122) is designed for X3000/X5000 right‑hand drive cabs with independent fan power. It houses the evaporator, heater core, blower motor, and mode doors. The unit is pre‑assembled with foam seals.
The filter housing (DZ13241841430) accepts a replaceable cabin air filter, improving interior air quality. The filter screen at fan inlet provides coarse debris protection.
Defrost ducts are precisely shaped to clear windshield fog. Foot ducts deliver warm air to the floor, improving driver comfort in cold climates.
The evaporator-compressor connection (DZ14251841043) and condenser-evaporator connection (DZ14251841078) are pre‑charged with compatible O‑rings. They are made of aluminum barrier hose with crimped ends.
Heating water pipe forming hoses (2 pieces) are pre‑molded to fit the tight engine bay routing. They resist cracking from high under‑hood temperatures.
The electric water valve bracket allows fitment of a solenoid valve for precise heater control. The heating component (heater core) provides 12 kW of heat output at nominal flow.
Hexagon flange bolts in M6 and M8 sizes (various lengths) secure the HVAC unit, brackets, and dryer tank. All bolts have pre‑applied threadlocker.
Reed nuts and tapping screws attach plastic ducts to the dashboard structure without pre‑threading. The ordinary narrow cable ties organize wiring harnesses away from moving doors.
Spring washers and flat washers ensure bolted joints remain tight under vibration. The type 1 hex nuts complement the flange bolts where double‑sided mounting is needed.
Step 1: Remove dashboard lower covers and old HVAC unit. Recover refrigerant if AC lines are disconnected.
Step 2: Install welding studs (DZ93189777172) on the firewall if missing. Mount the AC body assembly using M8x20 flange bolts. Torque to 25 Nm.
Step 3: Route defrost and foot ducts into position, securing with tapping screws and reed nuts. Install filter housing and filter screen.
Step 4: Connect evaporator and condenser lines using new O‑rings (included). Attach heater hoses to engine and heater core.
Step 5: Install drain pipe, rubber sheath, and drainage plug covers. Secure all lines with elastic clamps (29mm/30mm) and pipe clamps.
Step 6: Reconnect battery, test all modes (defrost, face, foot), and verify no refrigerant leaks. Evacuate and recharge AC system as required.
Weak airflow – clogged filter screen or broken mode doors. New AC body assembly restores full fan speed and door operation.
Water leakage inside cab – cracked drain pipe or missing plug cover. New drainage components prevent interior flooding.
No heat – corroded heater core or stuck water valve. Heating component and valve bracket solve this.
Rattling noises – loose air ducts due to broken clips. All fresh fasteners and ducts eliminate rattles.
AC body housing tested to -40°C to +85°C thermal cycling. No warpage or cracking. Heater core pressure tested to 5 bar burst.
Rubber hoses (EPDM) meet SAE J20R1, resistant to engine oil, coolant, and ozone. Elastic clamps have 480h salt spray rating.
All plastic ducts are made from flame‑retardant ABS/PP, meeting FMVSS 302. Filter screen is washable after 50,000 km.
Direct fit for Shacman X5000 and X3000 right‑hand drive models (2015‑2026). Also compatible with some X6000 after minor modifications (check AC body mounting points).
The AC body assembly uses independent fan power, meaning it works with both standard and high‑power alternator configurations. Not for left‑hand drive – order LHD version separately.
One‑stop ordering: 40 part numbers consolidated into a single kit, saving procurement time. Bulk discounts available for 5+ kits.
Installation time reduced by 40% because all hardware is included – no trips to hardware store for missing bolts or clips.
Driver comfort restored fully, reducing fatigue and improving safety (clear defrost). AC system warning sign included for legal compliance.
No, compressor is separate. This kit covers cab‑side components only: ducts, HVAC unit, heater hoses, AC lines and hardware.
Yes, it is a nylon mesh. Clean with soapy water and blow dry. Replace every 2 years or if damaged.
The AC lines and evaporator are compatible with R134a and R1234yf. Use the type specified by your truck’s system.
All hexagon flange bolts have a blue microencapsulated patch, active upon tightening. No additional threadlocker needed.
24 months on all components. Excludes damage from incorrect installation or physical impact.
In summary, the Shacman X5000 A-C Cab Components kit provides a complete, professional solution for cab climate system restoration. Choosing the Shacman X5000 A-C Cab Components ensures every duct, hose, and fastener meets original equipment standards. Every Shacman X5000 A-C Cab Components component – from the AC body assembly to the smallest spring washer – is backed by a 24‑month warranty. Upgrade your truck with the Shacman X5000 A-C Cab Components today. For bulk orders or technical support, use the Quotation button above. The Shacman X5000 A-C Cab Components kit is available for immediate dispatch from regional warehouses. Download the catalog for full exploded diagrams and torque specifications.
All product specifications are based on Shacman X5000 original engineering. Part numbers are genuine references. Always verify compatibility with your vehicle VIN before ordering. This kit contains small parts – keep away from children.
