The Shacman X5000 Mounting Bracket Assembly-Washing Pot is a complete OEM bracket kit for the washer fluid reservoir on Shacman X5000 and X3000 trucks. This assembly includes the mounting bracket and one welding square nut. The Shacman X5000 Mounting Bracket Assembly-Washing Pot securely holds the washing pot (windshield washer tank) in place, preventing vibration and leaks. Perfect for replacing corroded or damaged brackets, this Shacman X5000 Mounting Bracket Assembly-Washing Pot ensures factory‑fit mounting and long service life.
The Mounting Bracket/Washing Pot is a stamped steel bracket designed to hold the windshield washer fluid reservoir (washing pot) securely to the chassis frame. Made from 2.5mm thick DC04 steel with a black powder‑coat finish (e‑coat equivalent), it resists corrosion and vibration. Dimensions: 180mm long, 60mm wide, 40mm high. The bracket includes two pre‑drilled 8.5mm holes for chassis mounting and one 6.5mm hole for the welding square nut. It features rubber edge trim on the contact surfaces to prevent reservoir chafing. Direct replacement for the original Shacman X5000 part, this bracket eliminates rattling and ensures the washing pot stays fixed even on rough terrain. Operating temperature range -40°C to +85°C. Weight 0.35 kg.
One welding square nut is supplied. It is manufactured from hardened C67S spring steel, zinc‑plated (8μm thickness) with trivalent passivation, offering 480h salt spray resistance (ASTM B117). Dimensions: 15x15mm, height 4mm. Thread M8x1.25 rolled. The square nut is designed for projection welding onto the chassis or onto the bracket itself. After welding, it provides a captive, non‑rotating M8 thread. Pull‑out force exceeds 800 N. Essential for attaching the washing pot bracket to the chassis frame, this nut eliminates the need for a separate backing wrench during assembly. It is supplied pre‑oiled and packaged in an anti‑corrosion bag.
| Part Number | Part Name |
|---|---|
| Mounting bracket assembly components: | |
| DZ9718962307 | Mounting Bracket/Washing Pot |
| Welding fastener included: | |
| Q37106 | Welding Square Nut |
Complete kit – includes the mounting bracket and one welding square nut. No extra hardware to source. Ready to weld/install.
OEM quality: 2.5mm steel bracket with e‑coat, 480h salt spray. Welding nut is hardened spring steel with zinc plating.
Direct fit for Shacman X5000/X3000. Pre‑drilled holes match original chassis. Rubber edge trim prevents reservoir chafing.
Eliminates washer bottle rattling and movement. Restores proper fluid reservoir positioning. 24‑month warranty.
The washer fluid reservoir (washing pot) is a common component that can become loose or damaged if its mounting bracket fails.
Original brackets often rust through or bend, causing the reservoir to hang loose and eventually crack.
This kit provides a brand new stamped steel bracket that holds the washing pot firmly against the chassis rail.
The included welding square nut allows permanent, vibration‑proof attachment of the bracket to the frame.
All components are manufactured to Shacman original specifications, ensuring perfect alignment with the washer bottle.
Material: DC04 cold‑rolled steel, thickness 2.5mm. Surface: black powder‑coat e‑coat equivalent, 60‑80µm. Salt spray resistance 480h.
Dimensions: length 180mm, width 60mm, height 40mm. Weight 0.35 kg. Bracket includes two 8.5mm chassis mounting holes and one 6.5mm nut hole.
Rubber edge trim: EPDM, 2mm thickness, bonded to the inner edge to protect the plastic reservoir. Operating temperature -40°C to +85°C.
The bracket is designed to fit the original Shacman X5000 washing pot (part DZ9718964010). It can also accommodate aftermarket reservoirs with similar mounting points.
Material: C67S spring steel, hardness 42‑48 HRC. Zinc plating 8µm, yellow passivation. Salt spray 480h (ASTM B117).
Dimensions: 15x15x4mm. Thread M8x1.25 rolled. Four projection bumps for resistance welding.
Recommended welding current: 9‑11 kA, electrode force 2.8 kN. Pull‑out force >800 N after welding.
After welding, the thread may require re‑tapping with an M8 tap to remove any spatter. The nut is reusable, but we recommend welding it once.
Step 1: Remove the old bracket and washer reservoir. Drain any remaining washer fluid.
Step 2: Clean the chassis frame area where the bracket will be attached. Remove rust and paint.
Step 3: Weld the square nut (Q37106) onto the chassis frame at the factory‑marked location. Use a resistance welder with proper parameters.
Step 4: Position the new mounting bracket against the frame. Align the bracket’s two 8.5mm holes with existing holes or with the welded nut.
Step 5: Insert M8 bolts (not included) through the bracket into the welded nut and other chassis holes. Torque to 25 Nm.
Step 6: Reinstall the washing pot onto the bracket. The rubber edge trim should contact the reservoir without excessive force.
Step 7: Reconnect washer hoses and refill fluid. Test washer operation for leaks.
Rusted or broken mounting bracket – new steel bracket restores secure hold. Missing weld nut – new square nut provides captive thread. Loose washer bottle causing rattles – bracket with rubber trim eliminates noise. Corroded fasteners – zinc‑plated nut included. Leaking reservoir from movement – proper mounting prevents stress cracks.
Salt spray (ASTM B117): 480h on bracket – red rust <5% on cut edges. Welding nut 480h – no red rust, thread functional.
Vibration test (ISO 16750‑3): 10‑500Hz, 4.3 Grms, 48h – bracket did not crack, bolts remained tight, rubber trim intact.
Thermal shock: -40°C to +85°C, 100 cycles – no deformation, no adhesive failure on rubber trim.
Chemical resistance: 72h exposure to windshield washer fluid (methanol/water) – no swelling, no coating blistering.
Direct replacement for Shacman X5000 (2019‑2026) and X3000 (2015‑2026) washing pot brackets. Also fits X6000 with same chassis hole pattern.
Works with original washer reservoir (DZ9718964010) and most aftermarket units. Check bracket hole spacing before ordering.
Cost‑effective: replacing only the bracket is 80% cheaper than a full washer system replacement. Hardware included – no extra shopping.
Reduced downtime: installation under 30 minutes plus welding time. Eliminates rattling complaints from drivers.
Prevents washer fluid leaks: secure mounting avoids reservoir movement that causes cracks at hose connections.
Improves vehicle safety: a properly functioning washer system is essential for clear visibility.
Yes, the kit includes a projection welding nut that must be welded onto the chassis frame. If your original nut is intact, you can reuse it, but we recommend using the new nut for best results. If you lack a resistance welder, a local welding shop can do it in minutes.
The bracket comes powder‑coated black, ready to install. It matches the original chassis color and does not require additional painting.
Use two M8x25mm hex head bolts with flat washers. Bolts are not included – reuse original or purchase new. Torque to 25 Nm.
Yes, as long as the reservoir has a flat mounting surface approximately 60mm wide and the two mounting holes match the bracket’s slots (adjustable ±5mm).
24 months on bracket and welding nut against cracking, corrosion, or weld failure (if welded per instructions). Excludes improper installation or physical damage.
The bracket is pre‑formed with alignment dimples, making positioning easy. The rubber edge trim is pre‑applied, saving assembly time.
The welding square nut has four projection bumps for consistent weld quality, reducing rework. The kit includes an anti‑spatter bag for the nut.
Technical support: downloadable PDF includes weld parameters, torque specs, and a drilling template – available via catalog button.
The bracket is made from 30% recycled steel. Powder coating uses no VOCs. Welding nut is 100% recyclable. Packaging uses 100% recycled cardboard with water‑based ink, no plastic foam.
A concrete mixer fleet with 22 Shacman X5000 trucks had multiple washer bottles dangling due to rusted brackets. Using the Shacman X5000 Mounting Bracket Assembly-Washing Pot, they replaced all failed brackets in two days. The welding square nuts were installed by an on‑site welder in 10 minutes per truck. After 18 months, no bracket failures were reported, and washer fluid leaks were eliminated. The fleet saved over $2,500 in replacement reservoir costs.
Universal metal strips require cutting, drilling, and bending, often resulting in poor fit and sharp edges that cut the reservoir. Our bracket is pre‑formed with rubber trim to protect the plastic. Generic weld nuts from hardware stores are not designed for projection welding and may fall off; our nut has four projection bumps for reliable fusion. Aftermarket brackets are usually not coated, leading to rust in one winter; our bracket has 480h salt spray resistance. This kit includes the correct welding nut – no guesswork about thread size.
In conclusion, the Shacman X5000 Mounting Bracket Assembly-Washing Pot is the only OEM solution for washer reservoir bracket replacement. Choosing the Shacman X5000 Mounting Bracket Assembly-Washing Pot guarantees perfect fit, durable materials, and all necessary fasteners. Every Shacman X5000 Mounting Bracket Assembly-Washing Pot component is factory tested for extreme conditions. Upgrade your truck with the Shacman X5000 Mounting Bracket Assembly-Washing Pot today. For bulk orders or technical support, use the Quotation button above. The Shacman X5000 Mounting Bracket Assembly-Washing Pot is in stock and ready for immediate shipment. Download the catalog for full welding parameters and installation diagrams.
All product specifications are based on Shacman X5000 original engineering. Part numbers DZ9718962307 and Q37106 are genuine references. Always verify compatibility with your vehicle’s VIN before ordering. Professional welding equipment recommended.
